Octadecanethiol Monolayer on Silver

Procedure developed by George Lisensky based on the Tollens' Test and the well-known self-assembly of thiol monolayers (SAM) on gold surfaces.
The aldehyde group in glucose, , reduces Ag(NH3)2+ to Ag metal. The silver is then coated with a self-assembled monolayer of octadecanethiol, , making a non-polar surface on which water beads up.

Wear eye protection
Chemical gloves recommended

Place a clean microscope slide in a Petri dish.
Place 4 large drops of a 0.5 M glucose solution on the microscope slide.
Add 12 large drops of an active silver ion solution.
Gently agitate to mix the solution. Wait several minutes while the solution darkens and a grayish precipitate forms.

A silver mirror is also forming on the slide, though it may be obscured by the precipitate. Use water from a wash bottle to wash off the precipitate and reveal the silver mirror. Avoid contact with the solution since it will stain your hands. Discard the solution by rinsing with water and remove the slide from the Petri dish.

Wait for the surface to appear dry. (For faster drying use a hair dryer.)

Cover only part of the silver with a few drops of a long chain alkanethiol solution in ethanol. One way to do this is to rest the slide at an angle. Allow the ethanol to evaporate at room temperature (no hair dryer), leaving behind an alkanethiol monolayer with the sulfur atoms bound to the silver and the hydrocarbon tails pointing away. This effectively coats the surface with a monolayer of hydrocarbons.

How attracted are the water drops to the monolayer coated surface? To the silver surface? To the glass? Do water drops spread out or bead up? Like attracts like. Is the water attracted more to the plain glass, to the silver, or to the alkanethiol monolayer-coated silver?

The contact angle is between the side of a drop and the slide. Is the contact angle wide (small attraction to the surface) or narrow (large attraction to the surface) for each surface?

Classify the glass, the silver, and the alkanethiol coated surface as like or unlike the probe.

Materials for 25 students

  • 0.8 M KOH (Dissolve 0.22 g KOH in 5 mL of water.)
  • 0.1 M silver nitrate (Dissolve 0.17 g AgNO3 in 10 mL of water.)
  • 15 M ammonia (Concentrated aqueous ammonium hydroxide.)
  • Active silver ion solution, Ag(NH3)2+
  • Add concentrated ammonium hydroxide dropwise to 10 mL of 0.1 M silver nitrate solution until the initial precipitate just dissolves. Mix with a glass stir rod. Add 5 mL of 0.8 M KOH solution; a dark precipitate will form. Add more ammonium hydroxide dropwise until the precipitate just redissolves. This "active silver" solution should be used within an hour of preparation. Dispense from a dropper bottle. To avoid the formation of explosive silver nitride, discard any remaining active solution by washing down the drain with plenty of water.

  • 0.5 M glucose or dextrose (Dissolve 0.90 g in 10 mL of water. Dispense from a dropper bottle.) Sugar or sucrose does not work.
  • Alkanethiol solution. Add a very small amount (just barely visible) of a long-chain alkanethiol, such as octadecanethiol, to 20 mL of absolute ethanol. Dispense from a dropper bottle.
  • Equipment

  • Petri dish
  • Microscope slide (75 x 25 x 1 mm)
  • Droppers or dropping bottles
  • Wash bottle (water)
  • Hair dryer (recommended)

  • Exploring the Nanoworld   |   MRSEC Nanostructured Interfaces
    Copyright © 2008 The Board of Regents of the University of Wisconsin System.

    This page created by George Lisensky, Beloit College.  Last modified January 29, 2013 .